Give Me A Quote!

We have noticed this post relating to How to Install a Bathtub Yourself below on the net and thought it made perfect sense to talk about it with you on my blog.

Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old tub with a brand-new one is also a reasonably challenging project. If the old bathtub is easily easily accessible, the job can move rapidly; if you need to open up a wall surface to remove the old tub and also place the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's skills, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. Ensure you have actually certified on your own for the work and also fit trying it. As opposed to hiring a service provider to take control of a halfway-completed job, it is much better to think about using one prior to you begin. Chances are you might need an expert plumber to make tube links.
This short article will help you mount a brand-new bathtub in your shower room if you have actually currently bought a brand-new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your devices and product list should consist of the following:

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installment

First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable tap ports to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its final setting.

Removing Old Taps

If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the limited accessibility that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipes. When the supply pipelines have been removed, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this process. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before going on to fit the new taps, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

Setting up the Bathtub

Utilizing both wooden boards under its feet, position the tub in the called for setting. The wood boards are handy in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the tub till the level checks out degree.
To set up faucets, fit all-time low of the outermost flexible tap connector to the proper supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Activate the supply of water and also examine all joints and also new pipework for leaks and tighten them if required. Load the tub and additionally inspect the overflow electrical outlet as well as the typical electrical outlet for leaks.
Finally, repair the bathroom paneling as described in the manufacturer's user's manual. Tiling and also securing around the bath tub needs to wait till the tub has actually been made use of a minimum of when as this will certainly resolve it right into its final placement.

Fitting New Taps

If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in area in between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous type must be attached to the tap ends first, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

Tiling Around the Tub

In the location where the bathroom satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split a stiff seal, creating the water to permeate the wall in between the bath as well as the tiling, leading to problems with wetness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and also installations. They are sold in tubes and cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can crack rather early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently readily available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you really like reading up on How to Install a Bathtub? Make a review further down. We would be interested to see your feelings about this write up. We are looking forward that you come back again before long. For those who liked our blog entry kindly remember to pass it around. Bless you for your time. Don't hesitate to come by our website back soon.

Visit My Web Page